CNET CSH-2400W User's Guide Page 1

Smart Access Web Management Switch USER’S GUIDE 1

Fig 4-4 5. Log: log the server’s activity messages into a log file. 6. Help: view the help file. D. Click on the “Server Set

Fig 4-5 E. Please change the Server Port from “80” to “8888”, and press OK for it to take effect. The next window shows that it runs using port 888

Fig 4-6 F. From internet side, connect to the WAN IP of your LAN gateway with port 8888 as below: http://XXX.XXX.XXX.XXX:8888/proxy.htm . The

Fig 4-7 G. Select the Switch to be configured from the left side and the device information will be shown on the right. (Fig 4-8). Fig 4-8 13

Click on the “Configure this Device” to start the configuration of the selected Switch.(Fig 4-9) Fig 4-9 14

5 Configuring the Switch 5.1 How to login to the Switch 1. When a Switch is selected for configurati

Fig 5-2 5.2 Configuration Items The configurable features of the web smart Switch are listed in

Fig 5-4 Link Status – Indicates the link status of each port ON/OFF. Speed –Indicates Link Speed of each port 10/100. Duplex –Indicates Half-duplex o

Fig 5-5 2. Click on the “Counters” button (Fig 5-6), and the information we are looking for will be seen on Fig 5-7. Fig 5-6 18

Fig 5-7 3. You can click on the “Reset Counters” button (Fig 5-7), to reset the counter number. 5.2.2 Port Config

TABLE OF CONTENTS 1 UNPACKING INFORMATION... 3 2 PRODUCT IN

5.2.3 VLAN 1. Select port-based VLAN or tag-based VLAN. (Fig 5-9) Fig 5-9 2. Click on

3. Select VLAN Group Members,which are to be grouped together. 4. Click on the “Apply” to save the configuration. Fig 5-11 Note: Group 1 (All ports

Fig 5-12 5.2.5 802.1p/TOS Priority 1. Enter 802.1p/TOS Priority menu 2. Select the pri

2. Click on the “Apply” to save the configuration. Fig 5-14 5.2.7 General System Configuration

Fig 5-15 A. IP address: If the Switch is not a DHCP Client, select “Disable” for DHCP Client and fill out the IP Address, Subnet Mask and Default

Fig 5-16 To change Login Name and Password: 1. Type in the Login Name. The default Login Name is admin. 2. Enter a new password. The default passwor

Fig 5-17 2. Click on the “OK”. All your Switch’s settings will be restored to its factory default values. To upgrade the switch’s firmware: Please

6. HELPFUL SUGGESTIONS 6.1 Prior to Installation Before installing the Switch and connecting network devices, it is important to plan the network&apos

7. Product specifications Product Name CSH-2400W Ports 24 100BASE-TX/10BASE-T Ports Standards IEEE 802.3 10BASE-T IEEE 802.3u 100BASE-TX IEEE 802.3x

1 UNPACKING INFORMATION Thank you for purchasing this Switch. Before continuing, please check the contents of the product package. The package should

2 PRODUCT INTRODUCTION 2.1 Key Features ．Support up to 24 port-based VLAN Groups ．Support Store-and-Forward Technology Filtering/Forwarding to Elimina

2.3 The Rear Panel 19 inches case 2.3.1 Power Socket The Power Socket is designed to be used with the power cord included in the product package. ‧At

3 INSTALLATION 3.1 To locate the Switch on a desktop ．Attach the four rubber feet included in the product package to the bottom of the Switch, one in

4 SMART FUNCTIONS SETTINGS 4.1 Start Smart Function The Switch has a built-in smart function that can be accessed through a web browser and provides

C. The program will show.(Fig 4-2) Fig 4-2 Note: In the above window, there are 6 function icons that you can use to control the program: 1. St

Fig 4-3 4. Proxy Setting: View the existing Switches in this LAN, and also add/delete/modify any Switch in the LAN for configuration convenie